| stevehopwoodforex.com https://www.stevehopwoodforex.com/phpBB3/ Print view |
|
| HGIMatrix https://www.stevehopwoodforex.com/phpBB3/viewtopic.php?t=3973 |
Page 48 of 68 |
| Author: | JRforex [ Thu Apr 30, 2015 5:53 am ] |
| Post subject: | HGIMatrix |
Now that would be a very useful feature  IMHO the matrix is excellent as it is, there's no point in modifying it at this stage. JR |
|
| Author: | josch [ Thu Apr 30, 2015 7:28 am ] |
| Post subject: | HGIMatrix |
Agree, there is a point, from which you aren't able to improve something. josch |
|
| Author: | marcoFF [ Thu Apr 30, 2015 10:19 am ] |
| Post subject: | HGIMatrix |
Hi, thanks for the great tool! Sorry for my English, but I have a newbie question.. In the chart below the matrix show me at EURCAD below in the D1 chart. There was it, but after dissapeared from the chart but not from matrix, something wrong? No way to get a warning when it happens? Thank you. |
|
| Author: | renexxxx [ Thu Apr 30, 2015 10:35 am ] |
| Post subject: | HGIMatrix |
I think that you are referring to the Range UP Arrow on Candle 1, that has disappeared from the chart right? You didn't mention whether you are running the HGI-indi version of the HGIMatrix or the HGI-library version. In any case, here goes: 1. The HGI-indi version of HGIMatrix will only reload the HGI-indicator if the matrix itself is reloaded. The HGI-indicator does not update signals on previous candles, unless it is reloaded. A possible scenary, if you were running the HGI-indi version of the HGIMatrix, is that your refreshed your D1 chart (thereby reloading the HGI-indicator on that chart) such that the Range UP Arrow on Candle 1 was cleared, but you didn't reload the Matrix. Or ... 2. If you are running the HGI-library version of HGIMatrix, each signal for each candle is re-evaluated every minute automatically. So, it can be that the Range UP Arrow on Candle 1 (re) appeared, whilst it was not present on your D1 chart. If you want to make sure, just reload the matrix and the HGI-indicator on the D1 chart at the same time. You should get the same information. I admit, it must be hard for newbies ... sorry about that. |
|
| Author: | marcoFF [ Thu Apr 30, 2015 11:22 am ] |
| Post subject: | HGIMatrix |
Hi renexxxx thanks for the explanation and the patience. I think now i have understand what you mean, and this is why i use the indy version. So if i load a the HGI-library i see all the "new" signal of the current candle? And the indy warns me for all of that signal? Thanks again :hi: |
|
| Author: | renexxxx [ Thu Apr 30, 2015 11:28 am ] |
| Post subject: | HGIMatrix |
With the HGI-Library version (31L) you will get not only updated (new) signals for the current candle, but also for previous candles. There are various parameters to control which alerts you want to receive and where these alerts should be directed to. |
|
| Author: | marcoFF [ Thu Apr 30, 2015 11:46 am ] |
| Post subject: | HGIMatrix |
Ok, I do a little testing. Thanks again! |
|
| Author: | bharath4x [ Fri May 01, 2015 3:05 pm ] |
| Post subject: | HGIMatrix |
Hi Rene, I have an observation to report. Please see below. It is NZDJPY, H4 chart Screenshot 1: HGIMatrix Library Version shows big bearish trend arrow which does not exists in the chart. I even tried changing TF's but i did not get that on chart. I see this issue in other TF's too. Screenshot 2: Non Library version showing Big bearish trend arrow but there is none in chart I'm using HGI_v17.00 version with updateSecondsDelay parameter value = 0. Here too i tried changing TF's but did not get that big bearish trend arrow in chart. Please check and advice. |
|
| Author: | bharath4x [ Fri May 01, 2015 5:06 pm ] |
| Post subject: | HGIMatrix |
Hi Rene, Please advise, if there is a way to send selected alerts only for current candle [0] signal change. |
|
| Author: | renexxxx [ Fri May 01, 2015 9:10 pm ] |
| Post subject: | HGIMatrix |
The indi-version of HGIMatrix loads the HGI-indicator with its default parameters (except for isiCustom=true). That means that HGIMatrix loads HGI with updateSecondsDelay=30. You have set this to 0 on the chart. So, there is a difference. The library-version of HGIMatrix does not have an option for calling the HGI functions with different parameters. So, whatever signal is generated, is decided by how the code in the library was implemented. Cheers ... |
|
| All times are UTC | Page 48 of 68 |
|
Powered by phpBB® Forum Software © phpBB Limited |
|