03 - Pipcruiser Dashboard – Signals – EA - MPTM

pt2004 · Post by **pt2004** » Tue Feb 03, 2015 6:06 pm

Hi,

My platform was freezing, but after i loaded historical data seems to be OK.

gringoh · Post by **gringoh** » Tue Feb 03, 2015 6:15 pm

pt2004 » 03 Feb 2015, 19:06 wrote:Hi,

My platform was freezing, but after i loaded historical data seems to be OK.

As specified in post 1, Perfect,

Cheers,
G

gringoh · Post by **gringoh** » Tue Feb 03, 2015 6:18 pm

jimskin » 03 Feb 2015, 19:02 wrote:I did load the historical data first. It's showing 'Script ForceLoadHistoricalData EURUSDm,Daily: loaded successfully' in the Journal.

I'm using a Micro account which uses EURUSDm, etc...

My Dashboards have never been tested with brokers which are using a suffix...

I'll have to perform some tests to see how it goes.

You can try to change the pairs value in the dashboard input "ThePairs".

Please, let me know how it goes. (Which broker are you using?).

Cheers,
G

earlb38 · Post by **earlb38** » Tue Feb 03, 2015 8:03 pm

Not sure if i should ask this here so remove if wrong place

I have setup Dashboard from page 1 in Indi folder also MPTM from page 1 in Expert folder

but if i want to use Dashboard.tpl 2004 and EA.tpl 2004 do i put those on each of the 2 charts instead

the Dashboard.tpl brings up every thing on chart but with EA.tpl is it presetup with the setting as there is no way to check imputs and does not show as being an EA on the chart so seems wrong somehow

or am i doing this completely wrong

qvintus · Post by **qvintus** » Tue Feb 03, 2015 8:11 pm

How is this weeks results so far on this version of pipmasher?

nicolkoekoek · Post by **nicolkoekoek** » Tue Feb 03, 2015 8:25 pm

OneandOnly666 » Tue Feb 03, 2015 5:50 pm wrote:My platform freezes too.

getting 0 global varibles detected for the dashboard in the expert menu
//Thomas

I still have the same problem as well, I reinstalled a few times a new GP Empty4 today, got the ForceloadHistoricalData running successfully with failed:none. And I also have the "0 global variables detected" message when I load the Dashboard, followed by "initialized" and a hanging of the Empty4..

Nicolaas

Post by **macman** » Tue Feb 03, 2015 9:19 pm

nicolkoekoek wrote:I still have the same problem as well, I reinstalled a few times a new GP Empty4 today, got the ForceloadHistoricalData running successfully with failed:none. And I also have the "0 global variables detected" message when I load the Dashboard, followed by "initialized" and a hanging of the Empty4..
Nicolaas

What happens if you just run the dashboard (drag onto any chart) as an indicator without using a template?

Does it work?

gringoh · Post by **gringoh** » Tue Feb 03, 2015 9:45 pm

Don't worry with the information 0 global variables detected. During the dashboard init there is this control. I might remove it to avoid questions.

I use 1 chart for the dashboard & 1 chart for MPTM EA.

I will share my results at the end of the week, no need to ask everyday.

Cheers,
G

gringoh · Post by **gringoh** » Tue Feb 03, 2015 9:50 pm

As suggested by Macman, before to apply a template, first, you should try to attach the indicator directly to the chart to be sure that everything is working properly.

If you still have an issue please provide some informations:

- Broker used
- MTCrap build used
- Suffix or not

Cheers,
G

Post by **barry** » Wed Feb 04, 2015 1:08 am

gringoh » Wed Feb 04, 2015 4:06 am wrote:
barry » 03 Feb 2015, 07:35 wrote:I can't get the dashboard indicator to load on a chart. I have tried on two different computers, but the platform just hangs and becomes unresponsive, even after 30 mins.

Just to be clear, I have used a new GP platform, applied the ForceLoadHistoricalData script until there were no problems, closed and re-opened the platform, one eurusd H1 chart open only, applied PPC-DASH-2002.tpl. I can see the dashboard, but the platform is unresponsive and data flow in the lower RH corner shows 0/0kb.

On another platform, I limited the Max bars to 1,000 in Tools/Options/Charts, before doing all the above again, but same result, platform is unresponsive.

I don't know what else to try - I'd welcome any ideas, thanks.
Any news?

Which broker are you using?
Which MTCrap platform are you using?
Do you have any suffix with your broker like EURUSDm ?

Cheers,
G

Thanks gringoh. I just tried again, using the latest dashboard and ea from post 1. I have forced download of data, and then applied the dashboard, on two computers. The platforms still become unresponsive in my hands, even after waiting 15 mins . I am using Global Prime build 765 and there are no prefixes or suffixes.