Desky. TDesk's trading drone.

Post by **c1borg** » Mon Feb 11, 2019 5:04 am

Early testing which could definately be my fault, I had a Pending and a Super signal and no trade? I have another Demo with the same setfiles for both TDesk and Desky which is making trades? Will try and get some more useable feedback.

Capture.PNG

Capture1.png

Post by **c1borg** » Mon Feb 11, 2019 5:59 am

c1borg » Mon Feb 11, 2019 5:04 am wrote:Early testing which could definately be my fault, I had a Pending and a Super signal and no trade? I have another Demo with the same setfiles for both TDesk and Desky which is making trades? Will try and get some more useable feedback.

Ignore this atm I have tracked the issue to a combination of my setfile(s) and indicator. Will report back soon.

Post by **SteveHopwood** » Mon Feb 11, 2019 12:40 pm

wallywonka » Mon Feb 11, 2019 3:55 am wrote:
Hi Steve, I'm using grid orders and it doesn't appear to be deleting pending orders on opposite or flat signals, both are enabled.

werterherr just sent me the solution to this. Thanks werterherr.

The fix is in post 1.

DIYers, the faults are to be found in lines:
4817 if (SellOpen)
4809 if (BuyOpen)

These stop Desky from deleting pending orders if there is a market trade already open. Doubtless there was a reason for this at the time I coded it, but I cannot think what it was.

Change these lines to:
if (SellStopOpen || SellLimitOpen)
if (BuyStopOpen || BuyLimitOpen)

Your line numbers are probably a bit different to mine if you are an avid DIYer, so if in doubt do a search for, "//Following an opposite direction signal" to take you to the relevant code block.

Post by **SteveHopwood** » Wed Feb 13, 2019 4:52 pm

V 2t is in post 1. I have added the daily profit target thingy. The inputs are underneath the weekly profit target inputs.

Post by **wallywonka** » Fri Feb 15, 2019 5:24 am

Delete pending trades on signal change doesn't appear to be working here... Anyone else confirm this?

Post by **c1borg** » Fri Feb 15, 2019 6:07 am

wallywonka » Fri Feb 15, 2019 5:24 am wrote:Delete pending trades on signal change doesn't appear to be working here... Anyone else confirm this?

Working for me this just happened as an example.
pending order #117987446 sell stop 0.01 GBPUSD at 1.27932 deleted

Post by **wallywonka** » Fri Feb 15, 2019 6:10 am

c1borg » Fri Feb 15, 2019 6:07 am wrote:
wallywonka » Fri Feb 15, 2019 5:24 am wrote:Delete pending trades on signal change doesn't appear to be working here... Anyone else confirm this?
Working for me this just happened as an example.
pending order #117987446 sell stop 0.01 GBPUSD at 1.27932 deleted

Are you using grid trading or normal pending trades?

Post by **c1borg** » Fri Feb 15, 2019 6:35 am

wallywonka » Fri Feb 15, 2019 6:10 am wrote:
Are you using grid trading or normal pending trades?

Normal trades grid trading is off in this setup

Post by **wallywonka** » Fri Feb 15, 2019 7:38 am

c1borg » Fri Feb 15, 2019 6:35 am wrote: Normal trades grid trading is off in this setup

Cheers bud, not sure what is happening here... I made sure I have the latest version but pending trades just wont delete...hmmm

ppaulius1 · Post by **ppaulius1** » Fri Feb 15, 2019 6:13 pm

Hello,

I have the same issue. I'm using grid on two demos and pending orders are not deleted on flat signal. Tested on 'q', 's' and 't' versions - the same results.
Didn't test 'DeletePendingOrdersOnOppositeSignal' yet.

There is my .set file if somebody want to check/compare settings.