Hopelessly confused by TDesk or Desky? Ask here.

Post by **tomele** » Thu Jun 13, 2019 9:59 am

Hi.

First: You are using an outdated TDesk version. The actual Desky version will not work with that.

Second: Desky reacts only to Super Signals. Your Super Signal logic is set to AND/AND. As I can't see your Super and Multi Signals, I can't tell you what's going on. But most probably your Multi Signal is below the entry threshold.

Post by **isabek** » Thu Jun 13, 2019 11:13 am

tomele » 13 Jun 2019 12:59 wrote:Hi.

First: You are using an outdated TDesk version. The actual Desky version will not work with that.

Second: Desky reacts only to Super Signals. Your Super Signal logic is set to AND/AND. As I can't see your Super and Multi Signals, I can't tell you what's going on. But most probably your Multi Signal is below the entry threshold.

Huge thanks Thomas.

I switched off both Super and Multi signals and I use ver 6.6 on VPS, will try set them on and set SoloSignalsOnly.

Post by **isabek** » Mon Jun 17, 2019 7:03 pm

XAUUSDH4.png

Hi, Thomas.

Still have some confusion

GBPCAD signal is fired, but Desky seems to ignore it (SendImmediateMarketTrade=true; MaxOpenTradesAllowed=10; grid/offset/basket/recovery/hedging/cts and etc is set to false; no limits for time; no tradingdone for day/week; UseZeljko=true; OnlyTradeCurrencyTwice=false; no swap filters; margin is enough; MaxPairsAllowedToTrade=8;)

News affect only 3 hours before/after.

gbpcad_1.png

Any clues/hints?

Regards,

Isabek.

Post by **tomele** » Mon Jun 17, 2019 9:47 pm

Hi Isabek.

If TDesk's Super Signal is what it should be, it must be your Desky settings. Please post your setfile.

Thomas

Post by **isabek** » Tue Jun 18, 2019 7:35 am

Thanks for your time.

Set for Desky

desky nnf.set

Set for TDesk

tdesk nnf 6.7.set

XAUUSDH4_2.png

Again, CADCHF has given Signal, but no trade.
Before that EURCAD Signal was traded.

Regards,

Isabek.

Post by **bodavid** » Tue Jun 18, 2019 8:48 am

isabek » Tue Jun 18, 2019 2:35 pm wrote: Again, CADCHF has given Signal, but no trade.
Before that EURCAD Signal was traded.

Don't know if it helps, but I had the same problem and couldn't find any explanation.

So I reverted back to Desky v3g and that solved my problem.

Cheers,
Ben

Post by **isabek** » Tue Jun 18, 2019 9:09 am

Thank you, guys!!!
It happened that I use 3g version of Desky, will test 3p version now.

p.s. Found that there is a new version of TDeskSignals.mqh also.

Post by **tomele** » Tue Jun 18, 2019 9:50 am

isabek » 18 Jun 2019, 08:35 wrote:Thanks for your time.

Set for Desky

Set for TDesk

Again, CADCHF has given Signal, but no trade.
Before that EURCAD Signal was traded.

Regards,

Isabek.

Read about Zeljko in the documentation.

Post by **isabek** » Tue Jun 18, 2019 9:53 am

:hi: Thomas, thanks again!

My bad.

Post by **BobbyT** » Tue Jun 18, 2019 8:37 pm

Just wondering about the signal exclusion. I am having trouble getting it to work.

I would like to exclude a signal coming from UBD defined as "TDI-P" on H4. Thus, the signal appears on TDesk as "TDI-P1 H4".

What is the appropriate string to have this signal excluded from solo/multi signals.

Does this string require quoting or is that handled in the backend?

Cheers,
BobbyT