Hopelessly confused by TDesk or Desky? Ask here.

Post by **trader689** » Sat Sep 04, 2021 8:19 pm

hey ishak

same thing happened to me after my computer had an unexpected shutdown.

The thing I did to get it trading again was to close all the charts on my terminal and then reopen them and reapply the EA / templates

trader

ishak123 » Wed Aug 25, 2021 2:05 pm wrote: Why not Sharky making any trade when signals are oky. no clue whats wrong.
any idea.
Using below set file.

bhrunogomes · Post by **bhrunogomes** » Mon Sep 06, 2021 10:36 pm

I am not allowed to access the attachments. Can someone help me?

Post by **SteveHopwood** » Tue Sep 07, 2021 10:46 am

bhrunogomes » Mon Sep 06, 2021 10:36 pm wrote:I am not allowed to access the attachments. Can someone help me?

You can now.

MihxUp · Post by **MihxUp** » Wed Sep 15, 2021 7:22 pm

Hello there,

I hope one of the smart guys can figure out why my UBD for RSI (Builtin_5) is not sending any signals to TDesk.

The goal is actually quite simple:

Send a buy signal when RSI Value is below 30
Send a sell signal when RSI Value is above 70
RSI = 7,PRICE_CLOSE

Based on the image below there should be a buy signal for CHFJPY H4. But TDesk does not get any signals.
Interestingly, when setting up the same scenario for the built-in Stochastic indi it's working as designed.

UBD_RSI_NoSignal.png

Can someone take a look into the attached set-file and give me a hint, please?

Thanks and best regards,
Max

Post by **wallywonka** » Wed Sep 15, 2021 11:09 pm

Need to see your TDesk UBD Builtin Indicators.mq4 file

MihxUp · Post by **MihxUp** » Thu Sep 16, 2021 3:08 pm

wallywonka » Thu Sep 16, 2021 12:09 am wrote:Need to see your TDesk UBD Builtin Indicators.mq4 file

There you go.
The only thing I changed was the RSI period from 14 to 7 in that file. Otherwise, it is the default one.

Thank you for taking the time to look into it.

Best regards,
Max

Post by **tomele** » Thu Sep 16, 2021 4:39 pm

Your setfiles work here.

freakyg415 · Post by **freakyg415** » Thu Sep 16, 2021 7:15 pm

Big Pipping to all,

I have come to a bit of a bump in the road that I think can't be accomplished at this time; and am looking to see if anyone has a solution or if it is even possible. The goal is to use a USD signal and compare that to a fresh cross of current price i.e a 1 moving average close UBD. The key here is the USD signal(that populates for one candle only) stays constant until a new USD signal is populated meanwhile every fresh cross (or so many candles after the fresh cross) the UBD or USD sends a signal to Tdesk. The indicator I am using only has the USD function for the buffer i'd like to use and the other is the last candle close price. Any suggestions would be greatly appreciated. Thanks in advance.

V/r,
Osito

Post by **tomele** » Thu Sep 16, 2021 7:29 pm

freakyg415 » 16 Sep 2021, 20:15 wrote:The key here is the USD signal(that populates for one candle only)

No. Each signal stays valid until an opposite or flat signal occurs or SignalMaxAgeBars is reached.

freakyg415 · Post by **freakyg415** » Thu Sep 16, 2021 7:33 pm

tomele » Thu Sep 16, 2021 2:29 pm wrote:
freakyg415 » 16 Sep 2021, 20:15 wrote:The key here is the USD signal(that populates for one candle only)
No. Each signal stays valid until an opposite or flat signal occurs or SignalMaxAgeBars is reached.

Thanks Thomas. I figured it wasn't possible. Thanks for clarifying.