ADAPTING NB10.2A FOR LOWER TF & RM TRADING - 10.2A CTS

[disbellj]

Fable, I'll look into it.

Don

CC,

Glad you and others like it

I looked at ATeam. ATeam indicator itself uses iCustom, so didn't think it would help resources to use it. Would be using iCustom twice each pair each timeframe each tick. Also, it looks to only show up to D1 timeframe, where the indicator I've made shows up to MN1. If only needing H1 96 period, H4 and D1 13 period, then I can strip the rest of the timeframes and that should save resources. Just need your input on this, and I've got another update about ready to go, with (first attempt - hey, gotta start somewhere) Trade Entries based on user input of TradeMode.

Kindest regards,

Don

Great! Lookfing forward to see that. Btw, I'm asking again, could be possible to choose the pairs (I'd like to remove some, to save some CPU).

Regards,

Fable

[disbellj]

OK. I changed Semafor to ATeam as option 1. User can choose Option 2 (CountZZ function modified) or 3 (Mop/Don mtf method) also, for comparison.

Shows Emerging only if Aggressive Mode is set by user (3 in user inputs). Otherwise, Emerging not shown.

Wie and I gotta go give plasma so we can have some spending money.

Note: I noticed Semafors/ATeam is turned off, so if turned on, hopefully spacing will be correct. Will check when I have time.

Kindest regards,

Don

[fire580]

Odd - but I'm showing only 13 pairs each one listed twice?

[disbellj]

Try resetting indicator, removing and placing on chart again, or switch timeframes and switch back. This behavior is obviously not normal. BTW, when Empty4 starts, gotta do this too because things start off reading wrong.

Kindest regards,

Don

[fire580]

Hi Don - went from bad to worse - now completely locked up Empty4 - tried several times restart - removed indicator from my platform "indicators" and removed from my download file also removed the other two versions - still no hope - every time I turn on my platform AllPairs_CTS_Don 102912 still shows on chart but chart and entire platform frozen - really don't know what to do - never had this happen before - on other occasions deleting from platform indicators and even deleting downloaded culprit brought platform back to normal?

[Fable]

Hi Don - went from bad to worse - now completely locked up Empty4 - tried several times restart - removed indicator from my platform "indicators" and removed from my download file also removed the other two versions - still no hope - every time I turn on my platform AllPairs_CTS_Don 102912 still shows on chart but chart and entire platform frozen - really don't know what to do - never had this happen before - on other occasions deleting from platform indicators and even deleting downloaded culprit brought platform back to normal?

Go into 'profiles' and remove all chart from the profile you use should do the trick

[disbellj]

Hold up guys. Doing some testing.

1. I have MANY arrays in this indicator. I didn't know how many maximum pairs to set this this to. So I looked on Wikipedia for number of currency pairs and it's near 200 I think. SO that's what I put into indicator for int length and also array sizes. This slows the indicator down tremendously. SO I've set it back to 50. If you have more pairs than that, I guess we need to know what max to set it to, or you can go in at top of code and change 50 in length and arrays to be however many pairs you have.
2. CC misunderstood and said white was H1 and pink was H4. Really, H4 12 Semafor replaced H1 96 Semafor, so White is H4 and Pink is D1 and no Semafor is used on H1. So now we only have two columns for Semafors, now named ATeam. However, calling the ATeam indicator with iCustom is the main lockup/slowdown problem. Now that we only need ((12*1440)/60) = 288, we can now use Mop/Don method of mtf, or CountZZ donmod function
3. The arrays zznbrm set up were 600. Since we use 12, I made it 30. Much faster than 600 if using CountZZ function.

Still doing testing. But now must take a break to try and fix plumbing problem.

Kindest regards,

Don

[fire580]

Thank you Fable - deleted all charts in profile - no luck - deleted profile no luck, same profile comes up with the chart containing AllPairs - and everything freezes up immediately have to go to task manager to close?

[Fable]

Thank you Fable - deleted all charts in profile - no luck - deleted profile no luck, same profile comes up with the chart containing AllPairs - and everything freezes up immediately have to go to task manager to close?

The chart with allpairs, must be somewhere in 'profiles'. Your problem is odd. Try to reinstall Empty4, make a copy of your indie, template, EA, ... first.

Good luck.

Fable

ps: I do take backup from Empty4 file on a usb key. It's really convenient

[Fable]

Hold up guys. Doing some testing.

1. I have MANY arrays in this indicator. I didn't know how many maximum pairs to set this this to. So I looked on Wikipedia for number of currency pairs and it's near 200 I think. SO that's what I put into indicator for int length and also array sizes. This slows the indicator down tremendously. SO I've set it back to 50. If you have more pairs than that, I guess we need to know what max to set it to, or you can go in at top of code and change 50 in length and arrays to be however many pairs you have.
2. CC misunderstood and said white was H1 and pink was H4. Really, H4 12 Semafor replaced H1 96 Semafor, so White is H4 and Pink is D1 and no Semafor is used on H1. So now we only have two columns for Semafors, now named ATeam. However, calling the ATeam indicator with iCustom is the main lockup/slowdown problem. Now that we only need ((12*1440)/60) = 288, we can now use Mop/Don method of mtf, or CountZZ donmod function
3. The arrays zznbrm set up were 600. Since we use 12, I made it 30. Much faster than 600 if using CountZZ function.

Still doing testing. But now must take a break to try and fix plumbing problem.

Kindest regards,

Don

Keep up the good work Don. You are doing a great job !