Macd Stochastic Fractal MA5/25 Daily Marylin

[dudest]

Phil, do you have any running JPY buys?

Not for now, cause I have close manually all my trades last friday to bank +10%. But I had.

Kul, thanks

[dudest]

New EURJPY and CHFJPY trades taken today.

Let's see whether NFP helps them or not

Cheers

[niepce]

Ditto EURJPY CHFJPY on ICmarkets.

Took a GU on thursday early morning, but got killed by the ECB speech

[cuzgeorge]

Me too guys,
i had a single buy on GU yesterday and that got slaughtered eventually. Today, two terminals have made that loss back, and about 3 terminals losing. Just slightly.
2 days, so nothing to judge by yet.

marilyn 5july.png

The other terminals mostly have only got a buy on UC. The pictured above has the most trades.

regards
cuz

[phil_trade]

Hi all

WinDev/Empty4 system also took CHFJPY ans EURJPY.

Niepce, did you read my post concerning Margin required concern about broker, and comparaison between ICM/GPF ? it could affect EA a lot !

http://www.stevehopwoodforex.com/phpBB3 ... 503#p68503

[bodleytunes]

How does one modify the unified set file to work with 15M timeframes? do I change the 1440 mins to 15?

Cheers!!

Jon.

[Radar]

Hey Jon,

How does one modify the unified set file to work with 15M timeframes? do I change the 1440 mins to 15?

Cheers!!

Jon.

Yeah, change the 1440's to 15, the 240's to 5, and the W1's to 1440... There's a few other things that need adjusting too, like Virtual Stoploss, which is obvious, and a few others that aren't quite so obvious, (well, for me, anyways).

I had a good run at the start of the week on M15, but Marylin took it all back - and then some - by the end of the week.

I need to get my head around the parameters, and learn what to change, and by how much.

Have fun!

Radar =8^)

[niepce]

You might shorten the timers as well
DeltaTimeLiveTrades=86400; 24H min between two live trades.
DeltaTimeHistoTrades=14400; 4H min between last closed trade and the new one.

[dudest]

Yeah, change the 1440's to 15, the 240's to 5, and the W1's to 1440...

I'm wondering whether the W1's should be changed to 30 (instead of 1440) [ since M30 is the higher TF to M15, as W1 is to D1... ]

Mapping:
W1 --> M30 [30]
D1 --> M15 [15]
H4 --> M5 [5]

Also, in addition to the ones Niepce has pointed out above, you can consider checking these:

a) StochLevelMaxToTrade = Upper stoch boundary to allow a long order. Automatically revert for shorts.

b) StochOBOSToMoveSL = Upper stoch boundary to set SL to BE if crossed, for long orders. Automatically revert for shorts.

c) StochH4LevelMax = Upper stoch boundary if using the H4 stoch option. More reactive. Probable more false positives, though.

d) UseStochD1slowToFilterTrade = Only take orders if immediate slow stoch slope in agreement.

e) UseStochH4ToTakeTrade = Enable Stoch H4 instead of D1.

f) DeltaPipsFromSRZoneToTakeTrade = How near is the next most-hit SR zone. Below this value, trade won't occur.

g) UseRSI_W1_ToTrade = Weekly range filter toggle.

h) ValeurRSI_W1_ToTrade = Upper boundary. Lower is computed internally.

i) UseRSI_W1_ToCloseTrade = Weekly range filter trade closure toggle. Will close open trades if market start to range again.

j) ValeurRSI_W1_ToCloseTrade = See above, same idea.

In creating the unified set, I opened the given pair's charts ( D1, W1) and placed the Stoch's and RSI and tried to determine values that would have worked for long/short trades. Then when I had the values for each pair, I decided to 'harmonize' ( rough 'best case' ) to keep things simple.

Attached: thought process & findings during this time ( + params explanation ). Hope it comes in handy.

Cheers!

[phil_trade]

Yeah, change the 1440's to 15, the 240's to 5, and the W1's to 1440...

I'm wondering whether the W1's should be changed to 30 (instead of 1440) [ since M30 is the higher TF to M15, as W1 is to D1... ]

Mapping:
W1 --> M30 [30]
D1 --> M15 [15]
H4 --> M5 [5]

Also, in addition to the ones Niepce has pointed out above, you can consider checking these:

a) StochLevelMaxToTrade = Upper stoch boundary to allow a long order. Automatically revert for shorts.

b) StochOBOSToMoveSL = Upper stoch boundary to set SL to BE if crossed, for long orders. Automatically revert for shorts.

c) StochH4LevelMax = Upper stoch boundary if using the H4 stoch option. More reactive. Probable more false positives, though.

d) UseStochD1slowToFilterTrade = Only take orders if immediate slow stoch slope in agreement.

e) UseStochH4ToTakeTrade = Enable Stoch H4 instead of D1.

f) DeltaPipsFromSRZoneToTakeTrade = How near is the next most-hit SR zone. Below this value, trade won't occur.

g) UseRSI_W1_ToTrade = Weekly range filter toggle.

h) ValeurRSI_W1_ToTrade = Upper boundary. Lower is computed internally.

i) UseRSI_W1_ToCloseTrade = Weekly range filter trade closure toggle. Will close open trades if market start to range again.

j) ValeurRSI_W1_ToCloseTrade = See above, same idea.

In creating the unified set, I opened the given pair's charts ( D1, W1) and placed the Stoch's and RSI and tried to determine values that would have worked for long/short trades. Then when I had the values for each pair, I decided to 'harmonize' ( rough 'best case' ) to keep things simple.

Attached: thought process & findings during this time ( + params explanation ). Hope it comes in handy.

Cheers!

Hi Dudest

Good stuff ! some precision :

e) UseStochH4ToTakeTrade = Enable Stoch H4 instead of D1

Should not be "instead" but also
Param OK for AUDUSD which STOCH D1 too quickly go to OBOS zone

b) StochOBOSToMoveSL = Upper stoch boundary to set SL to BE if crossed, for long orders. Automatically revert for shorts.

Move SL on best OpenPrice not BE. To use with DeltaPipsMoveSLOnStoch paramaters
-> ProfitInPips need a minimum to move SL on Best Open Price after Stoch reach OBOS zone

Philippe