10.7/10.9 INDI SOLUTIONS

[milanese]

Lydia,

You should read the first pages of the 10.6 thread, Bob explains it all.

Hi Elixe,

Thanks for the reply, I know 10.6 dummy light but what I don't understand is dummy light in DWMopen bar indi beacuse of the light sometimes they are full color, sometimes they are half green half red and sometimes

Cheers.

Post http://www.stevehopwoodforex.com/phpBB3 ... 478#p93478 and ff will explain it ..

Cheers

Tommaso

[Lydia]

Post http://www.stevehopwoodforex.com/phpBB3 ... 478#p93478 and ff will explain it ..

Cheers

Tommaso

Thanks Tommaso

[nanningbob]

What is the difference between TMA TRUE and ATR channels ????? NONE I put these on the screen using 60 and they are the same.

[nanningbob]

Here is the ATR with lines set at 1.0 3.0 and 4.0 ATR lines using the 60 MA

[nanningbob]

Here is the TMA using the 60 MA I used with 10.6. It runs dead center.

[nanningbob]

Conclusion. There is no real difference between the TMA true and ATR channels. They are basically the same indicator, when using the same numbers.

[Cherry]

Thanks Bob.
I'm more confused about the different TMA's. Why the True or the TMA_CG, or which to use?
I thought it was the TMA_CG we were using but Dave's looked a bit different but it could just be different broker time that caused it. Also if the settings were not correct in the inputs. I had been using it as it was in the download. Have since changed it as i said in my last post but not sure if that is correct either!

[nanningbob]

Thanks Bob.
I'm more confused about the different TMA's. Why the True or the TMA_CG, or which to use?
I thought it was the TMA_CG we were using but Dave's looked a bit different but it could just be different broker time that caused it. Also if the settings were not correct in the inputs. I had been using it as it was in the download. Have since changed it as i said in my last post but not sure if that is correct either!

You have to remember one thing about indicators. If they move with price they are nothing more than a Moving Average indicator with some kind of math formula. So in a sense they are all the same or will give about the same information. They may picture the information differently and nice little windows to see the information but in essence they show the MA in a certain light. In trading what you want to have is one that draws horizontal lines and one that draws angle lines. Learn to read them and its intricacies and you will have the basics down.

High low indicators like TMA, COG, Bollinger Bands, 5ths indi etc. all have their fans but are basically tell the same story. It is just a matter of reading them and getting to know them. So the differences are just variations of a theme. My 10.7 system is designed to fit any of the above. Basically what I am saying it really doesnt matter which one you choose but choose one and learn it. I just wanted people to know they can be made to say almost the same thing if you plug the right numbers into them.

[Cherry]

Thanks bob, got your idea now.

[freeman]

I am having a computer log on problem with my compter at school.
I have WIndows 7 Ultimate
There are 3 users on my computer
2 of them can log in but I cannot.
I tried system restore and that didnt work
I tried Scan/fix now prompt and it found no errors.
I tried my W7 disk but it does not have a repair function. It can only write the whole program over everything again.

When I enter my password to log in I get this message:

User Profile service failed log in
User Profile Cannot be loaded

I also went in under administrator under another log on and changed my password but that didnt work either.

Any solutions??

Try this :

1. Restart your computer and hit F8 multiples times until you see a menu-like screen, if you see the Windows splash screen then repeat this step
2. Highlight and hit enter on Safe Mode with Command Prompt. Try logging in there. If it still doesn't work, then go to step17
3. If you are able to login, once a command prompt pops up, type: net user administrator password /active:yes (you can specify whatever password you want for the administrator account.)
4. If you get a message saying "The command completed successfully", then restart your computer by typing: shutdown -r
5. Boot up again pressing F8, but this time choose just Safe Mode.
6. You will be able to login as Administrator with the password you set in Step 3
7. Hit (windows logo)+R
8. Type regedit
9. Once the registry editor opens up, look for HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
10. In the left pane, find the one that starts with S-1-5..... and ends with .BAK; if you don't find one, skip to step 15
11. Right click it and click Rename, then change the .BAK to .BK
12. Right click the one with the same numbering but without the .BAK and add .BAK add the end
13. Right click the one that you renamed to .BK and clickRename, delete the .BK
14. Eventually, you have switched the .BAK from the end of the second entry to the first. That should probably fix your problem.
15. If you didn't find a .BAK then try this: Open Windows Explorer to C:\Users\Default\AppData\Local\Application Data
16. If you find another Application Data below the one you're on, then delete it. That should probably also fix your problem.
17. If you can't login in Safe Mode, then reboot and hit F8 until you see the menu again, then hit enter highlightingRepair Your Computer
18. Wait until all Windows Files finish loading, then hitNext when it asks keyboard language.
19. Try logging in here also, choose your user from the dropdown menu, and type the password, then jump to step 23
20. If that still doesn't work, then if you have your Windows Installation CD still, put it in and restart your computer.
21. Hit F12 until you see a menu of boot options, choose Boot from CD
22. Choose keyboard language then hit next. Find Repair Your Computer from a little below the center left.
23. Choose Open Command Prompt and type: net user administrator password /active:yes (here again you can specify a password)
24. Close the command prompt and click Restart and jump to step 5

To disable the administrator account, type this in an elevated command prompt: net user administrator /active:no

Cheers

Tommaso

Tommaso,
Just noticed that in addition to doing a shipload of coding, pointing people in the right direction (as you did for me), you also provide general IT help. Be Blessed!